Doggy Bag Holder

May 19th, 2015 § 0 comments

Paper-Calliope-Whisker-Graphics-Doggy-Bag-Holder-1

Okay Napolean, here’s a little something to throw together before the humans get back from the NSS. It’s sure to impress and may even give you a few doggie points (which frankly you may need after being alone for the past week!) For those of you who haven’t met Napolean, check us out on Facebook. He’s the French Bulldog that has taken over the shop this week while the human owners of Whisker Graphics are away at the National Stationery Show in NY. He’s running all kinds of specials, so follow us and stay tuned. This project comes to us from crafty, design team member, Betsy Skagen.  It’s a handy doggie bag holder. It’s right next to the leash so you can grab one on your way out the door. Wrapped in Polka Dot Middy bags and Napolean’s paw print and bone, it’s perfectly practical.

Paper-Calliope-Whisker-Graphics-Doggy-Bag-Holder-2

Here’s what you need:

Here’s how you make it, according to Betsy:

Step 1–Eat a lot of oatmeal

Step 2–Use the oatmeal container as your base for the doggie bag holder. Give the container and lid a coat or two of gesso so the graphics do not show through your paper covering.

Step 3–Reinforce the lid of the oatmeal container with strips of packing tape. I’m not entirely sure why packing companies now make their lids out of half cardboard/half plastic rather than all plastic, but it certainly makes it more flimsy.

Step 4–Lightly sand the gesso-covered container.

Step 5–Measure the height of the jar. If you are mathematically inclined, or you have a cloth measuring tape, you can also measure the diameter. Or, if you are lazy like me, you can wing it.

Step 6–Cut the closed end off a Red Polka Dot Bigger Bitty Bag and peel off the glued strip. Cut along the seam and trim the edge so that you end up with a large rectangular sheet of paper. Repeat with a second sheet.

Step 7–Trim the paper to the size of the container

Step 8–Cut open another Green Polka Dot Middy Bitty Bag and trace the lid and the end of the container onto the back of the Middy Bag paper. Cut out these circles. Draw doggy themed shapes onto this paper and cut out.

Step 9–Adhere the doggy themed shapes to a piece of coordinating cardstock and cut out.

Step 10–Cover the container in a thin coat of Mod Podge. Carefully wrap the container in your polka dot paper, leaving a little hanging off the open end. Cut small slits in the overhanging paper, fold down and adhere to the inside of the container.

Step 11– Punch a hole in each side of the container, about 1/2 inch from the top. Thread a length of Divine Twine Single Petites through the punched holes  and tie together inside the container in order to form a handle.

Step 12–Cover the lid and the container end with a thin coat of Mod Podge. Carefully adhere the two circles you previously cut out. Let dry.

Step 13–Adhere a decorative ribbon to the top edge of the container.

Step 14–Cut a small X in the lid of the jar.

Step 15–Adhere the doggy themed shapes to the container.

Now all you need to do is add some doggy bags, threading the first through the X you cut, close the lid and hang your new doggy bag holder.

Betsy has a fun blog with whimsical projects always presented with a good dose of humor! Be be sure to check it out  at Paper Calliope.

Leave a Reply

Your email address will not be published. Required fields are marked *

What's this?

You are currently reading Doggy Bag Holder at Whisker Graphics.

meta

  • Categories

  • Subscribe to Blog via Email

    Enter your email address to subscribe to this blog and receive notifications of new posts by email.

  • Petite Stickys
  • Bitty Bags
  • blog roll
  • Archives